Generic0

• Fully compatible with micro:bit board.
• All micro:bit pins can correspond to the sections on the expansion board.
• It can be directly plugged into the breadboard.
• Allow you to connect multiple modules.
• This adapter will help you in various DIY creations and experiments.

• 2 x micro:bit pins set.
• 1 x micro:bit edge connector.
• Dimensions: 7 x 5 x 2 cm (Approx.)

PLEASE NOTE:

Misusing or mishandling a lithium-ion battery may cause a FIRE or EXPLOSION which can result in INJURY or DEATH.

This is high quality 18650 battery with a typical capacity of 3350mAh. It is Lithium-Ion based and rechargeable battery (with proper charger) in a cylindrical shape. 18650 battery has become very popular nowadays, many power bank is using it as storage and power source. Even the famous Electrical Vehicle like Tesla is using 18650 batteries particularly to build their battery pack. 

And since the single-cell voltage and capacity are high, rechargeable, it is a very economic solution in electronic or robotic projects. In some cases, this battery has been used for IoT devices powered by solar or other renewable energy. The battery becomes an energy storage device. And of course, it can be series up to get higher voltage, for example connecting 2 units in series to get ±7.4V (nominal) or 3 units to get ±11.1V using the 18650 battery holders. Or in some cases, it is being parallel up to increase the capacity and discharge current.

Please do charge it using a proper charger with a balancer. Li-ion battery should be charged and discharged properly to prevent short lifespan and downgrade of its capacity. We recommend using any of these chargers:

Note: This is 18650 Li-Ion Battery comes with both end (positive and negative) flat metal terminals and there is no protection circuit, so please take extra precaution.

You might also need the proper 18650 sockets/holders to use this battery:

• Single 18650 battery holder
• Two 18650 battery holder (in series)

• INR18650C-3350B01 Datasheet

• Washer
• M5 x 10 mm OD
• Zinc Plated
• Mild Steel

• M6x16 slotted cheese head screws
• Nylon
• Ideal for VESA connectors when mounting your Pi on big TV's

PLEASE NOTE:

Misusing or mishandling a lithium-ion battery may cause a FIRE or EXPLOSION which can result in INJURY or DEATH.

The Samsung INR21700-50E li-ion battery is one of the most powerful and reliable cells available in the 21700 size, and boasts a 5,000mAh capacity that's sure to keep your electronic devices running longer. The battery is often used for consumer-devices that require a high discharge rating, and are often built into small 21700 battery packs. The ICR chemistry should always be used with protective circuitry.

Specifications

• Technology: Li-ion
• Capacity: 5000mAh
• Form Factor: 21700
• Min. Capacity: 4753mAh
• Nominal Voltage: 3.6V - 3.7V
• End-of-charge Voltage: 4.2V
• End-of-discharge Voltage: 2.5V
• Max. Current Output Constant: 9.8A
• Max. Current Output Pulse: 14.7A
• Charging Current: 2.45A
• Max. Charging Current: 4.9A
• No Protection Circuit
• Positive Pole (structure): flat top
• Dimensions: 21.2 x 70.7mm
• Net Weight: 70g

Important Safety Warning

The user must have appropriate understanding of lithium ion batteries before purchase. Use caution when working with and using lithium ion batteries as they are very sensitive to charging characteristics and may explode, burn, or cause a fire if misused or mishandled. 

• ONLY USE WITHIN MANUFACTURER LISTED SPECIFICATIONS
• DO NOT short circuit
• DO NOT overcharge or over-discharge
• DO NOT solder, spot weld only
• Usage of batteries is AT YOUR OWN RISK
• ALWAYS charge in or on a fire-proof surface and never leave charging batteries unattended

What's in the box?

1 x 21700 Li-ion battery

You might also need a suitable battery charger

Resources

• Datasheet
• Samsung Safety Information

This user-friendly heatsink set, made of efficient aluminum, effortlessly cools your machine. Just peel and stick on RAM, VGA card, or any compatible equipment. With a sleek design and dimensions of 14x19x7mm, it ensures optimal cooling.

Specifications

• Material: Aluminium
  
• Colour: Black
  
• Size: 14mmx19mmx7mm
  
  
  

What's in the box?

1 x Aluminium Heat Sink

• Material: Aluminum
• External dimension: 19*14*7mm
• Colour: Black
• Weight: 2g/pcs

• Ideal for pc, laptop, ps4, ps5, xb1, xb series x/s, and switch consoles.
• 40mm drivers, with high-quality magnets providing a perfect sound
• Comfortable ear cushions designed for full-ear coverage
• Long cable (160cm) with in-line controller 

• Speakers Diameter: 40mm
• Frequency response: 20Hz - 20KHz
• Impedance: 32 Ohm +- 15% @ 1KHz
• Sensitivity: 92 Ohm +-3dB @ 1KHz
• Input Power: 30mW(Max)

• Frequency Response: 100Hz - 10KHz
• Signal-to-noise ratio: >58dB
• Sensitivity: -40dB +- 3dB @ 1KHz
• Pick-up pattern: Omnidirectional boom

• 90 Watt High Power
• For all popular laptops
• Automatic Voltage Sensing
• Worldwide Use
• 20 Tips Included
• AC Input: 100~240V AC
• DC Output: 12~20V DC
• Connection Type: 20 Assorted DC Tips

We sourced this cable so that we could plug a keyboard into PicoVision and play Doom, but it could be used to connect a USB accessory or peripheral to any micro-B host device that supports USB OTG (On-The-Go), such as a Raspberry Pi Pico / Pico W or a Pi Zero W / Zero 2 W*.

⚠ Using USB in experimental ways can damage your USB ports and your devices, please only use cursed USB cables like this if you know what you're doing!

Notes

You might also need a NVMe board. 

These DIN rail mountable enclosures are designed specifically for the Raspberry Pi 5.

The kit comes complete with DIN rail hook for ultra-fast mounting.

The unit features 36mm internal clearance from the Raspberry Pi PCB to the top of the case, so there's plenty of room for GPIO mounted expansion boards.

Resources

1. press the rail lock by forefinger, then push it out by thumb as the picture shown



2. remove the bottom panel from the main part



3. fix the Raspberry Pi onto the bottom panel by screws



4. put on the bottom panel, aligning it with the buckle and USB connectors



5. snap another side



6. insert the rail lock (note the different sides, don't be upside down)

Outdoor electrical junction boxes are designed to keep sensitive electrical connections protected and secure in any environment, even underground. 


Specifications

• Surface Mounting Enclosure
• Junction Box with Plain Screwed Lid
• IP55 Limited protection from dust and low-pressure water jets from any direction
• Internal Dimensions Approx -150mm x 110mm x 70mm

What's in the box?

1 x Junction Box

Pic is for illustration purposes only

Great for mounting your Raspberry Pi into an enclosure or any other mounted position. Fits the 2.5mm mounting holes provided on your Raspberry Pi

Features

• M2.5x20 slotted cheese head bolt
• Stainless steel
• Fits through the mounting holes on the RPI board

What's in the box?

1 x bolt

A worthy choice for your PC upgrade

GIGABYTE Gen3 2500E SSD adopts Phison’s controller and high-quality 3D NAND, delivers up to 2400 MB/s sequential read and 1800 MB/s sequential write performance. By utilizing Host Memory Buffer technology, the SSD controller can access the host DRAM without performance loss. Furthermore, GIGABYTE Gen3 2500E SSD features TRIM, SMART, and Over-Provision support to secure your data and perform stably.

Breaking the Barriers of SATA Limitations (1TB)

Outstanding performance

• GIGABYTE Gen3 2500E SSD provides performance for your daily computing tasks, boast of best controller & 3D NAND flash.
• Sequential read speeds up to 2400 MB/s***
• Sequential write speeds up to 1800 MB/s***
• GIGABYTE Gen3 2500E SSD gives you faster data transferring experience compared to 2.5" SATA solid state drive.
• Host Memory Buffer (HMB)

The Host Memory Buffer (HMB) feature utilizes the DMA (Direct Memory Access) of PCI Express to allow SSDs to use some of the DRAM on PC system, instead of requiring the SSD to bring its own DRAM.

* HMB feature is only supported by Windows 10 & 11.

*** Speeds quoted are not applicable when used on Raspberry Pi

Power Saving While Operating

Comparing with regular PCIe 3.0 x4 SSD, GIGABYTE Gen3 2500E SSD reduces about 40%+ power while operating. Power consumption of the GIGABYTE Gen3 2500E SSD is notably improved.

SSD Tool Box

The newly updated SSD Tool Box is a software that gives users an overview of the SSD Status and various aspects such as model name, FW version, health condition and sensor temperature. Moreover, users can clear all the data with the Secure Erase function. You can download the SSD Tool Box from the link.

What's in the box?

1 x M.2 NVMe SSD

You might also need a NVMe board. 

These Lithium Batteries are a superior choice due to their combination of long lifespan (2000 cycles), high discharge capabilities (low internal resistance), and advanced safety features (integrated BMS) - all translating into a better investment compared to traditional lead acid batteries they can effectively replace.

Common Applications

• Gate motors
• Alarm panels
• UPS (Uninterrupted Power Supply)
• Toys
• Torches

Specifications

• Capacity in Ah: 8Ah
• Capacity in Wh: 102.4Wh
• Nominal Voltage1: 2.8v
• Maximum Continuous Discharge Current: 16Amps
• Peak Discharge Current (60 sec): 22Amps
• Charge Voltage: 13.8-14.6V
• Maximum Continuous Charge Current: 8Amps
• Short circuit protection: Yes
• Over voltage protection: Yes
• Under voltage protection: Yes
• Over current protection: Yes
• Charge Temperature: 5°C – 45°C
• Discharge Temperature: 0°C – 45°C
• Terminals: F1 – 4.75mm flat
• Weight (net): 1000g
• Dimension (L x W x H): 151 x 65 x 95 mm
• Number of Cycles (minimum) 100% DOD: 2000

What's in the box?

1 x 12.8v 8Ah Lithium Phosphate Battery

Please note: Pic is for illustration purposes only. This fan's connector is for Raspberry Pi 5, not the one shown in the pic.

This tiny but powerful 30mm fan can be used to keep your Raspberry Pi 5 cool.

It comes with a JST connector for the Raspberry Pi 5, allowing the fan to be controlled by software (the same way as the official Active Cooler).

Specifications

• Dimensions: 30x30x07mm
• Bearing Type: Sleeve
• Connector: Raspberry Pi 5 4-pin fan header
• Rated Voltage: DC 5V
• great for use with your own enclosures and designs

What's in the box?

1 x DC Fan 30x30x7mm

The TTGO T-Beam ESP32 LoRa 868MHz is built around a dual-core ESP32 chip, with 4MB of SPI flash onboard, providing both Wi-Fi and Bluetooth LE via a “3D antenna” on the PCB. The board’s LoRa operates at 868MHz and comes with an included SMA antenna. While location tracking is provided by the onboard u-blox NEO-6M GPS module with ceramic antenna.

Specifications

• MCU    ESP32
• Flash    4MB
• PSRAM    8MB
• Serial Chip    CH9102
• Wireless protocol    Wi-Fi + Bluetooth 4.2
• PMU    AXP192
• Onboard functions     3 Buttons (Power+IO38+Reset)

Antenna

• 3D WiFi Antenna [Use by default], (Support WiFi IPEX external antenna, but you need to jump resistance)
• LoRa antenna
• GPS ceramic antenna

GPS

• NE0-6M GPS Modules: Support GPS protocol
• Onboard RTC crystal, Support interrupt/ wakeup

LoRa

• Long Range Low Power LoRa Transceiver
• High sensitivity: -i48dBm
• Transceive rate: 300 kbps
• Optional Hardware
• SX1276[868Mhz]

Display Details

• OLED: 0.96 inch 
• Driver: SSD1306

Software

• Meshtastic - See Resources below
• Meschtastic firmware

Power Supply Mode

Support USB Micro/ 18650 battery holder [USB can power the battery]

Need batteries? You will find our battery selection here

What's in the box?

1 x T-Beam
1 x 433Mhz or 868Mhz Antenna
1 x 0.96 inch 128X64  OLED
2 x Pin

Resources

If you need technical support please check the links below to find more details.