Generic1
Specifications
- Shrinkage Ratio: 2:1 (will maximum shrink to 1/2 its supplied diameter)
- Cutting method: Scissors or sharp knife
What's in the box?
1 x 1m heat shrink tube
Arduino is an open-source electronics platform based on easy-to-use hardware and software. Arduino boards are able to read inputs - light on a sensor, a finger on a button, or a Twitter message - and turn it into an output - activating a motor, turning on an LED, publishing something online.
Specifications
- Arduino compatible board
- Microcontroller ATmega328
- Operating Voltage 5V
- Input Voltage (recommended) 7-12V
- Input Voltage (limits) 6-20V
- Digital I/O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins 6
- DC Current per I/O Pin 40 mA
- DC Current for 3.3V Pin 50 mA
- Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader
- SRAM 2 KB (ATmega328)
- EEPROM 1 KB (ATmega328)
- Clock Speed 16 MHz
- Length 68.6 mm
- Width 53.4 mm
What's in the box?
1 x UNO R3
1 x USB cable
Resources
Find more info on Arduino at https://www.arduino.cc/en/Guide
UNO R3 is a microcontroller board based on the ATmega328P.
The Arduino Uno R3 comes in two models; the normal version and the SMD version. In the SMD version you have the Atmega328 controller IC as an SMD chip soldered into the board, whereas in the normal version the IC is held on the Arduino by an IC Holder.
Features
- 14 digital input/output pins (of which 6 can be used as PWM outputs)
- 6 analog inputs
- a 16 MHz quartz crystal
- a USB connection
- a power jack
- an ICSP header
- a reset button.
It contains everything needed to support the microcontroller. Simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
What's in the box?
1 x Arduino Uno SMD
1 x Headers
1 x USB cable (Cable colour might differ prom product pic)
Resources
Getting started with Arduino products
A tiny and lovely clear acrylic enclosure for the raspberry pi zero. It designed to be beautiful, light, and easy-assembly. Perfect for any use (but especially for those who want to carry their Pi around in their pocket!). This enclosure is only compatible with the Raspberry Pi Zero! The case is as minimal as it gets coming in just two pieces of acrylic that secure with four screws. Made of crystal-clear acrylic, this case keeps the Pi Zero secure.
There are two USB holes and one cooling hole, you can use all of the connectors on the edges of the Pi: mini HDMI, micro SD slot, micro USB power, and micro USB port. There's also a cut out to allow a 2x20-pin header to be soldered onto the Pi Zero.
This case is also available in black
Features
- Easy to assemble
- 2 layers, 4 bolts, spacers and nuts included
- Will fit Raspberry Zero & Zero 2
Notes
Only includes the case. RPi Zero is not included.
Don't forget to remove the protective film from the acrylic.
What's in the box?
1 x Clear acrylic top plate
1 x Clear acrylic bottom plate
1 x heatsink
4 x acrylic spacers
4 x M2.5 screws
4 x M2.5 nuts
A tiny and lovely clear acrylic enclosure for the raspberry pi zero. It designed to be beautiful, light, and easy-assembly. Perfect for any use (but especially for those who want to carry their Pi around in their pocket!). This enclosure is only compatible with the Raspberry Pi Zero! The case is as minimal as it gets coming in just two pieces of acrylic that secure with four screws. Made of crystal-clear acrylic, this case keeps the Pi Zero secure.
There are two USB holes and one cooling hole, you can use all of the connectors on the edges of the Pi: mini HDMI, micro SD slot, micro USB power, and micro USB port. There's also a cut out to allow a 2x20-pin header to be soldered onto the Pi Zero.
This case is also available in clear acrylic
Features
- Easy to assemble
- 2 layers, 4 bolts, spacers and nuts included
- Will fit Raspberry Zero & Zero 2
Notes
Only includes the case. RPi Zero is not included.
Don't forget to remove the protective film from the acrylic.
What's in the box?
1 x Black acrylic top plate
1 x Black acrylic bottom plate
1 x heatsink
4 x acrylic spacers
4 x M2.5 screws
4 x M2.5 nuts
These electrical connectors are designed for ribbon cables and telecommunications applications. They are also referred to as insulation-piercing contacts (IPCs).
Specifications
- 40 Pins Male Standard 0.1" 2.54mm Row spacing
- Low Profile with mounting ears
- 0.1" Pin spacing 0.1" Row spacing, Mates with IDC & PCB male Receptacles
- Insulation Displacement Connector terminates to 0.050" (1.27mm) flat ribbon cable
What's in the box?
1 x 40-PIN IDC SOCKET CABLE MOUNT
Specifications
- Primary input voltage: 19V
- Input Voltage Min: 14V
- Maximum input voltage: 35V
- Fixed output voltage: 12V
- Pressure drop: 2V
- Output channel number: 1
- Number of pins: 3
- Output current: 1.5A
- Package Type: TO-220 Tube
- Operating temperature range: 0℃ to 150℃
- SVHC (Highly Concerned Substances): No SVHC (20-Jun-2011)
- Device number: 7812
- Tolerance, operating voltage : 4%
- Voltage Rectifier Type: Positive Fixed
- Maximum supply voltage: 27V
- Power supply voltage minimum: 14.5V
- Surface Mount Devices: Through Hole Installation
What's in the box?
1 x TO-220 Voltage Regulator IC
You might also need a heatsink for your regulator
Resources
Understanding How a Voltage Regulator Works
Specifications
| Color | Size | Wavelength(nm) | Voltage(V) | MCD | Lens color |
| Red | 5mm | 620-630 | 1.8-2.3 | 800-1000 | Red diffused |
| Yellow | 5mm | 580-590 | 1.8-2.3 | 800-1000 | Yellow diffused |
| Green | 5mm | 520-530 | 2.8-3.6 | 800-1000 | Green diffused |
| White | 5mm | 6000-6500k | 2.8-3.6 | 14000-16000 | Clear |
| Blue | 5mm | 460-470 | 2.8-3.6 | 800-1000 | Blue diffused |
What's in the box?
10 x Yellow LED 5mm
Resources
Specifications
- Size: (Approx.)12x12x7.3mm
- Life: 100000 times
- Quantity: 10pcs
- Current: 50mA
- Voltage: 12V
What's in the box?
10 x Push Button Switch
Resources
Specifications
- Colour: Black
- Buzzer Type: Piezoelectric
- Sound Pressure Level 85 dB
- Rate Voltage: 12V DC
- Operating Voltage: 3 - 24V
- Max Current Rating 11mA
- Frequency 3900±500Hz
- Drive Method: Drive Circuit Built in
- Mounting Holes
What's in the box?
1 x Piezoelectric Buzzer
Resources
- Python library
- Using a Buzzer With a Raspberry Pi
Simply plug this tiny module into the GPIO header on the Raspberry Pi and away you go!
- DS3231 RTC IC
- Self-adjust 3.3V and 5V
- Size: 14x14x12 mm
Features
- Smaller
- Work in 3.3V and 5V
- Supported Raspberry Pi and Arduino
What's in the box?
1 x RTC Module
1 x Battery
Resources
IR (Infrared) sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 3V to 5V so it's great for use on the Raspberry Pi!
To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to ground and listen on pin 1. It doesn't do any decoding of the signal, just passes the 'raw data' along.
Specifications
- Carrier Frequency: 38kHz
- Transmission Range: 45m
- Directivity: 45°
- Supply Voltage Min: 2.5V
- Supply Voltage Max: 5.5V
- Supply Current: 350µA
- Opto Case Style: Through Hole
- Operating Temperature Min: -25°C
- Operating Temperature Max: 85°C
- Packaging: Each
- Operating Temperature Range: -25°C to 85°C
- SVHC: No SVHC (16-Dec-2013)
- Supply Voltage Range: 2.5V to 5.5V
- Manufacturer: VISHAY MINICAST AGC2
What's in the box?
1x Infrared Receiver
Resources
IR sensor with filter at 38KHz, perfect for receiving commands from a TV remote control. Runs from 2.7V to 5.5VDC so it's great for any microcontroller, which include Arduino running at 3.3V or 5.0V, and of course include Raspberry Pi which run at 3.3V.
To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to ground and listen on pin 1. It doesn't do any decoding of the signal, just passes the 'raw data' along. Check the VS1838B datasheet for more details.
- IR Remote Control Receiver
- Built-in Filter at 38KHz
- Wide operating voltage range: 2.7V to 5.5VDC
- Compatible with Arduino, Raspberry Pi
- Simple interface to use it
What's in the box?
1 x infrared receiver
The only downside is they use the Dallas 1-Wire protocol, which is somewhat complex, and requires a bunch of code to parse out the communication. If you want something really simple, and you have an analog input pin, the TMP36 is trivial to get going.
We toss in a 4.7k resistor, which is required as a pullup from the DATA to VCC line when using the sensor.
Cable specs
- Stainless steel tube 6mm diameter by 30mm long
- Cable is 36" long / 91cm, 4mm diameter
- Contains DS18B20 temperature sensor
- If your sensor has four wires - Red connects to 3-5V, Black connects to ground and White is data. The copper wire is soldered to the wire shielding
- If your sensor has three wires - Red connects to 3-5V, Blue/Black connects to ground and Yellow/White is data
DS18B20 Technical specs
- Usable temperature range: -55 to 125°C (-67°F to 257°F)
- 9 to 12 bit selectable resolution
- Uses 1-Wire interface- requires only one digital pin for communication
- Unique 64 bit ID burned into chip
- Multiple sensors can share one pin
- ±0.5°C Accuracy from -10°C to 85°C
- Temperature-limit alarm system
- Query time is less than 750ms
- Usable with 3.0V to 5.5V power/data
What's in the box?
1 x DS18B20 Digital temperature sensor
1 x 4.7k resistor
Resources
Adafruit's Raspberry Pi Lesson: DS18B20 Temperature Sensing
- Has the ability to control eight separate appliances or pieces of equipment
- Eight on-board optoisolators enable direct interfacing to microcontrollers
- Eight red LED status lights on-board show relay activity
- Widely used in PLC control or smart home control
- 4 x M3 mounting holes for easy fixing via standoffs
- 15-20mA drive current needed per channel
- Relay coil maximum operating voltage: 5V
- Relay coil maximum current: 89.3mA
- Relay contact maximum: AC250V at 10A or DC30V at 10A
- No. of relays/channels: 8
- Item size: 134 x 55 x 20mm
- Item weight: 116g
- 1 x 8 Channel Relay Module
Warning
Exercise proper caution when connecting mains driven equipment or appliances to relay module as lethal current will be present.
This flexible 4x4 matrix keypad is connected to an 8 pin DuPont Female connector. It can be attached to a surface via the adhesive back by removing the white protective paper backing.
- Contact Resistance: 10Ω-500Ω
- Insulation Resistance: 100MΩ 100V
- Key Operating Force: 150-200N
- Circuit Rating: 35V DC, 100mA, 1W
- Dielectric Strength: 250V RMS (50-60HZ/Min)
- Electric Shock Jitter: ï¼ÂÂÂ5ms
- Operating Temperature: -40 deg. C ~ 80 deg. C
- Storage Temperature: -40 deg. C ~ 80 deg. C
- Vibration: 20G, max
- Size: 68mm x 76mm
What's in the box?
1 x 4x 4 Matrix Array Membrane Keypad
Resources
Specifications
- Each Relay has LED indication when ON
- SPDT Relays with terminal block outputs.
- Relay Coil voltage: 5 VDC
- Power Requirement: 5 VDC
- 10A 250V AC / 10A 30V DC
What's in the box?
1 x Four channel 5V DC Relay Module
Resources
Interfacing with a relay : https://tutorials-raspberrypi.com/raspberry-pi-control-relay-switch-via-gpio/
Specifications
- Each Relay has LED indication when ON
- SPDT Relays with terminal block outputs.
- Relay Coil voltage: 5 VDC
- Power Requirement: 5 VDC
- 10A 250V AC / 10A 30V DC
What's in the box?
1 x Two channel 5V DC Relay Module
Resources
Interfacing with a relay : https://tutorials-raspberrypi.com/raspberry-pi-control-relay-switch-via-gpio/
Features
- Display Colour: Red
- The black line connects to the negative electrode, red line connects to positive pole of power supply, white line connects to positive pole of tested power supply
- Material: Plastic Shell
- Display Digit: 3
- Measuring Range: DC 4.5-30V
Working voltage: 4.5-30V - Overall Dimension: Approx 28mm x 47mm x 21mm
Specifications
| Colour | Size | Wavelength(nm) | Voltage(V) | MCD | Lens colour |
| Red | 5mm | 620-630 | 1.8-2.3 | 800-1000 | Red diffused |
| Yellow | 5mm | 580-590 | 1.8-2.3 | 800-1000 | Yellow diffused |
| Green | 5mm | 520-530 | 2.8-3.6 | 800-1000 | Green diffused |
| White | 5mm | 6000-6500k | 2.8-3.6 | 14000-16000 | Clear |
| Blue | 5mm | 460-470 | 2.8-3.6 | 800-1000 | Blue diffused |
What's in the box?
10 x Blue LEDs
Resources