Search

Add touch control to your electronics projects in seconds! The BMT Capacitive Touch Module is a "plug-and-play" sensor that works just like a smartphone screen. With just three pins (VCC, GND, and Signal), it is incredibly easy to wire to any microcontroller.

Our 2 x D type battery holder is perfect for hobbyists looking for a reliable power source for their DIY electronics projects.

Argon ONE V3 Case is made compatible for Raspberry Pi 5 with upgraded features and all new black finish.

The ESP32-C5-WIFI6-KIT is a development board designed by Waveshare based on the ESP32-C5-WROOM-1 module for dual-band Wi-Fi and multi-protocol IoT gateway applications.

Creality Hi Ceramic Heating Block, High Thermal Conductivity, Quick-swap Nozzle, 300℃ High Temperature Resistance

The BME680 is a "4-in-1" sensor that measures temperature, humidity, barometric pressure, and volatile organic compounds (VOC) gas. It is a favorite for weather stations and air quality monitors

The GY-BMI160 is a highly integrated, low-power 6-axis inertial measurement unit (IMU) designed for precise motion tracking. It combines a 16-bit digital, 3-axis accelerometer and a 3-axis gyroscope into a single compact module, making it an ideal choice for space-constrained and battery-sensitive applications.

This 5-Port Passive Hub board has 5 vertical JST SH 1mm connectors in a row, all with the power, ground and SDA/SCL pins connected. There are also breadboard breakout pins if you need them. Use this hub to add as many I2C devices to the bus as you need.

This 4-wire cable is a little over 150mm long and fitted with JST-SH (Qwiic/STEMMA QT) female 4-pin connector on one end, and female jumper wires on the other.

This 4-wire cable is a little over 300mm long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.

These are handy for extending a Stemma QT or Qwiic cable if you don't have one long enough for your project, or to protect a port if you're regularly swapping out sensors/dev boards. The pin connections are 1-1, matching both sides.

This 4-wire cable is a little over 200mm long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.

Rotary encoders are soooo much fun! Twist em this way, then twist them that way. Unlike potentiometers, they go all the way around and often have little detents for tactile feedback.

The Adafruit Proto Under Plate PiCowBell is intended to be treated like a mini solder-less proto plate to simplify programming and sensor connectivity for your Raspberry Pi Pico board. Reset button? Yes! STEMMA QT / Qwiic connector for fast I2C? Indeed.

This Qwiic/STEMMA GPIO connector from Ozzmaker allows you to easily connect Qwiic or STEMMA enabled modules to a Raspberry Pi, without the need for soldering.

Animate your LEGO® Technic™ models using the high-performance LEGO Powered Up Large Motor. Specially engineered to handle heavy-duty tasks, this motor delivers the raw torque needed to drive complex gear setups, heavy lifting assemblies, or precise steering mechanisms.

Animate your LEGO® Technic™ models using the high-performance LEGO Powered Up Large Motor. Specially engineered to handle heavy-duty tasks, this motor delivers the raw torque needed to drive complex gear setups, heavy lifting assemblies, or precise steering mechanisms.

Single-cell lithium base battery charger & protection module. The charging will be via a micro B connector. Lithium base battery includes Li-po and Li-ion battery as the charging and discharging characteristic is similar.